2023 Ford GT Mk IV - by Ddiaz Design - Advanced
This simulation was performed with Advanced accuracy settings, using air as the fluid, a moving model positioned on ground, and an inflow velocity of 180.00 kph.
April 14, 2026
April 14, 2026
2023 Ford GT Mk IV - by Ddiaz Design - Advanced
This simulation was performed with Advanced accuracy settings, using air as the fluid, a moving model positioned on ground, and an inflow velocity of 180.00 kph.
Thank you for choosing AirShaper to analyze and optimize the aerodynamic performance of your design. This report presents the results of the aerodynamic simulation and provides insight into key flow characteristics, performance metrics, and areas for potential improvement. The objective of this analysis is to support informed design decisions through clear visualization and interpretation of aerodynamic behavior.
The findings presented in this report are intended to serve as a foundation for further development and optimization. If additional clarification or advanced analysis is required, further assistance is available through the AirShaper expert team via info@airshaper.com
The calculation results provided by AirShaper are based on a virtual wind tunnel simulation. The dimensions of this virtual wind tunnel are significantly larger than the flow phenomena shown in the result visualizations. As such, the model is not constrained or "clamped" by virtual walls, and boundary effects on the results are minimized.
Despite the high accuracy of modern computational methods, all simulations represent a simplification of real-world conditions. The results are subject to modeling assumptions, numerical discretization, and iterative solution errors. Consequently, simulation results should be interpreted as indicative rather than exact.
For safety-critical or highly sensitive applications, it is strongly recommended to validate simulation findings through physical wind tunnel testing. Assistance in identifying a suitable wind tunnel facility for your project is available upon request. Please contact info@airshaper.com for further support.
Drag, or air resistance, is the force of the wind on an object in the direction of the wind. It is composed of pressure drag (pushing/pulling normal the surface) and friction drag (sliding over the surface). In most cases the pressure drag is dominant. The drag coefficient is a dimensionless quantity that indicates the aerodynamic resistance of an object moving through its medium. It is defined as follows (note: the Cd value in this report has been corrected for blockage):
The Cd provides a measure for the aerodynamic efficiency of an object. By approximation, the actual drag force Fd on the object as well as the power required to propel it will vary in function of the wind speed according the following formula:
For your project, that leads to the force & power curves shown below. Please keep in mind that this curve is an estimation, based on extrapolation from the simulation wind speed. For more accurate forces at a given velocity, please perform a simulation for that velocity.
The coefficients below indicate the aerodynamic performance of your vehicle (all of them have been corrected for in terms of blockage factor).
Drag coefficient: the efficiency at which the vehicle moves through the air (lower drag means less fuel / energy consumption). Lift coefficient: the effectiveness of the vehicle to generate lift (positive value) or down force (negative value). The front & rear lift coefficient denote the split of the lift coefficient between the front & rear wheels.
| Symbol | Meaning |
| A | Reference area (m²) |
| Cd | Drag coefficient |
| Cl | Lift coefficient |
| D | Drag force (N) |
| L | Lift force (N) |
| U | Velocity (m/s) |
| ρ | Fluid density (kg/m³) |
| x, y, z | Cartesian components |
These are the dimensions of the bounding box around the object after rotation and scaling - according to the dimensions of the virtual wind tunnel (X = flow direction, Y = sideways, Z = vertical)
| X | 5.17 meters |
| Y | 2.06 meters |
| Z | 1.09 meters |
| Frontal Area | 1.959 m² |
| Planform Area | 9.763 m² |
The following parameters define the virtual wind tunnel environment and calculation settings used in this simulation:
| Accuracy | Advanced |
| Position | On Ground |
| Fluid | Air |
| Motion | Moving |
| Wind Velocity | 180.00 kph |
| Reference Orientation | Roll: 90° Pitch: -90° Yaw: 0° |
| Orientation | Roll: 0° Pitch: 0° Yaw: 0° |
| Units | Mm |
| Scale | 0.01 |
| Simulation name | 2023 Ford GT Mk IV - by Ddiaz Design - Advanced |
| Date Created | Apr 14, 2026 |
| Number of Cells | 134,885,521 |
| Solver Type | RANS - steady state |
| Turbulence Model | k-omega SST |
| Density | 1.225 kg/m³ |
| Viscosity | 1.47e-05 m²/s |
Wind tunnel coordinate system (shown on images): origin set to the center of the object and the axes aligned with the air vector
Model Coordinate System: origin location & axis orientation as provided with the original 3D file
Wind tunnel coordinate system - top view
Wind tunnel coordinate system - left view
The aerodynamic force acting on the object due to the airflow is resolved into three orthogonal components:
Fx – Drag Force: Acts parallel to the direction of the incoming wind.
Fy – Lateral Force: Acts perpendicular to the wind direction in the horizontal plane.
Fz – Lift Force: Acts perpendicular to the wind direction in the vertical plane.
Negative values indicate a force acting in the direction opposite to the arrows shown below.
Pressure force: Arises from the pressure difference between two opposite sides of an object. It is the sum of all the local forces pushing or pulling perpendicular to the surface.
Friction force: Arises from the wind sliding across the surface of the object. It is the sum of all the local friction forces parallel to the surface.
The aerodynamic force acting on the object due to the airflow is resolved into three orthogonal components:
| Forces | ● Fx | ● Fy | ● Fz | |
| Pressure | N |
1.57e+03
|
1.27e+00
|
-5.43e+03
|
| kg | (1.60e+02) | (1.29e-01) | (-5.54e+02) | |
| Viscous | N |
9.12e+01
|
2.11e-01
|
4.36e+00
|
| kg | (9.29e+00) | (2.15e-02) | (4.44e-01) | |
| Total | N |
1.66e+03
|
1.48e+00
|
-5.43e+03
|
| kg | (1.69e+02) | (1.51e-01) | (-5.54e+02) |
| Forces | ● Fx | ● Fy | ● Fz | |
| Pressure | N |
-1.27e+00
|
-5.43e+03
|
-1.57e+03
|
| kg | (-1.29e-01) | (-5.54e+02) | (-1.60e+02) | |
| Viscous | N |
-2.11e-01
|
4.36e+00
|
-9.12e+01
|
| kg | (-2.15e-02) | (4.44e-01) | (-9.29e+00) | |
| Total | N |
-1.48e+00
|
-5.43e+03
|
-1.66e+03
|
| kg | (-1.51e-01) | (-5.54e+02) | (-1.69e+02) |
The aerodynamic moments acting on the object due to the airflow is resolved into three orthogonal components:
| Forces | ● Mx | ● My | ● Mz | |
| Pressure | Nm |
1.64e+01
|
-1.65e+03
|
-9.83e+00
|
| kg·m | (1.67e+00) | (-1.68e+02) | (-1.00e+00) | |
| Viscous | Nm |
-4.47e-01
|
1.43e+01
|
6.58e-01
|
| kg·m | (-4.56e-02) | (1.46e+00) | (6.70e-02) | |
| Total | Nm |
1.59e+01
|
-1.64e+03
|
-9.18e+00
|
| kg·m | (1.62e+00) | (-1.67e+02) | (-9.35e-01) |
| Forces | ● Mx | ● My | ● Mz | |
| Pressure | Nm |
7.94e+02
|
-9.84e+00
|
-1.57e+01
|
| kg·m | (8.09e+01) | (-1.00e+00) | (-1.60e+00) | |
| Viscous | Nm |
-6.47e+01
|
6.57e-01
|
5.64e-01
|
| kg·m | (-6.60e+00) | (6.70e-02) | (5.75e-02) | |
| Total | Nm |
7.29e+02
|
-9.18e+00
|
-1.51e+01
|
| kg·m | (7.43e+01) | (-9.36e-01) | (-1.54e+00) |
The coefficients below indicate the aerodynamic performance of your vehicle (all of them have been corrected for in terms of blockage factor).
The drag coefficient was computed using the reference area defined in the Nomenclature and the velocity
The scale illustrates typical Cd values. More streamlined objects will have a low Cd, less streamlines objects will have a high Cd. The Cd of your project has been indicated as well.
Please note that this is an indicative figure, mainly suited for comparing different concepts. For a highly accurate value, contact us at info@airshaper.com.
For your project, that leads to the force & power curves shown below. Please keep in mind that this curve is an estimation, based on extrapolation from the simulation wind speed. For more accurate forces at a given velocity, please perform a simulation for that velocity.
Underpressure zones are areas with a pressure lower than that of the local surrounding air. Often these zones are caused by abrupt changes in shape, most pronounced by abrupt changes in cross section or surface geometry. Smooth these out to lower drag.
The following images provide insight into which features of your object are causing drag by showing "clouds" of low pressure.
Total Pressure Coefficient (Cp)

Front

Back

Top

Bottom

Left

Right
Surface pressure shows how air pressure is distributed across the object. Overpressure (Cps near +1) occurs where airflow decelerates, while underpressure (negative Cps) forms where it accelerates. Both contribute to drag — smooth transitions between high and low pressure regions to reduce it.
Cps

Front

Back

Top

Bottom

Left

Right
Friction drag is caused by air sliding across the surface. The faster the air moves, the higher the friction force. A smooth surface can reduce friction drag.
The images below show friction drag mapped in color on the surface. Surface streamlines reveal flow detachment: straight lines indicate attached flow, while curly patterns indicate separation – a common source of increased drag.
N/m²

Front

Back

Top

Bottom

Left

Right
Streamlines visualize how air flows past your object. Steady lines indicate laminar flow, while swirling patterns reveal turbulence. Separation occurs when airflow detaches from the surface — typically due to sharp angles or geometric disturbances — and is a common source of increased drag.
m/s

Front

Back

Top

Bottom

Left

Right

Front

Back

Top

Bottom

Left

Right
Noise estimation by means of simulations is an advanced field of engineering. Therefore, more simplified models ('acoustic analogies') have been introduced to obtain a rough estimation of the local noise generation without going through prohibitively expensive simulations.
To reduce the noise generation in your design, look for the origin of these "noise clouds" in the following images. Typically, noise is generated slightly downstream of the location where the flow is disturbed. Smoothen the source and you can reduce noise generation. Avoid cavities and external parts.
Noise Generation (dB/m³)

Front

Back

Top

Bottom

Left

Right
m/s
Top
Left
Cpt
Top
Left