AirShaper

Aerodynamic Simulation Report

Tesla Roadster - public 3D model

This simulation was performed with Regular accuracy settings, using air as the fluid, a moving model positioned on ground, and an inflow velocity of 100.00 kph.

October 19, 2026

Tesla Roadster - public 3D model

Introduction

Thank you for choosing AirShaper to analyze and optimize the aerodynamic performance of your design. This report presents the results of the aerodynamic simulation and provides insight into key flow characteristics, performance metrics, and areas for potential improvement. The objective of this analysis is to support informed design decisions through clear visualization and interpretation of aerodynamic behavior.

The findings presented in this report are intended to serve as a foundation for further development and optimization. If additional clarification or advanced analysis is required, further assistance is available through the AirShaper expert team via info@airshaper.com

Disclaimer

The calculation results provided by AirShaper are based on a virtual wind tunnel simulation. The dimensions of this virtual wind tunnel are significantly larger than the flow phenomena shown in the result visualizations. As such, the model is not constrained or "clamped" by virtual walls, and boundary effects on the results are minimized.

Despite the high accuracy of modern computational methods, all simulations represent a simplification of real-world conditions. The results are subject to modeling assumptions, numerical discretization, and iterative solution errors. Consequently, simulation results should be interpreted as indicative rather than exact.

For safety-critical or highly sensitive applications, it is strongly recommended to validate simulation findings through physical wind tunnel testing. Assistance in identifying a suitable wind tunnel facility for your project is available upon request. Please contact info@airshaper.com for further support.

Definitions

Drag Coefficient

Drag, or air resistance, is the force of the wind on an object in the direction of the wind. It is composed of pressure drag (pushing/pulling normal the surface) and friction drag (sliding over the surface). In most cases the pressure drag is dominant. The drag coefficient is a dimensionless quantity that indicates the aerodynamic resistance of an object moving through its medium. It is defined as follows (note: the Cd value in this report has been corrected for blockage):

C d = 2F d ρv 2 A

Force and Power Curves

The Cd provides a measure for the aerodynamic efficiency of an object. By approximation, the actual drag force Fd on the object as well as the power required to propel it will vary in function of the wind speed according the following formula:

F d = ρ · v 2 · A · C d 2 P = F d · v

For your project, that leads to the force & power curves shown below. Please keep in mind that this curve is an estimation, based on extrapolation from the simulation wind speed. For more accurate forces at a given velocity, please perform a simulation for that velocity.

Aerodynamic Coefficients

The coefficients below indicate the aerodynamic performance of your vehicle (all of them have been corrected for in terms of blockage factor).

Drag coefficient: the efficiency at which the vehicle moves through the air (lower drag means less fuel / energy consumption). Lift coefficient: the effectiveness of the vehicle to generate lift (positive value) or down force (negative value). The front & rear lift coefficient denote the split of the lift coefficient between the front & rear wheels.

Symbols

Symbol Meaning
A Reference area (m²)
Cd Drag coefficient
Cl Lift coefficient
D Drag force (N)
L Lift force (N)
U Velocity (m/s)
ρ Fluid density (kg/m³)
x, y, z Cartesian components

3D Model

These are the dimensions of the bounding box around the object after rotation and scaling - according to the dimensions of the virtual wind tunnel (X = flow direction, Y = sideways, Z = vertical)

3D Model

Bounding Box Dimensions (3D Model)

X 4.93 meters
Y 2.41 meters
Z 1.27 meters
Frontal Area 2.56 m²
Planform Area 10.794 m²

Simulation

Setup

The following parameters define the virtual wind tunnel environment and calculation settings used in this simulation:

Key Input

Accuracy Regular
Position On Ground
Fluid Air
Motion Moving
Wind Velocity 100.00 kph
Reference Orientation Roll: 0° Pitch: 0° Yaw: 0°
Orientation Roll: 0° Pitch: 0° Yaw: 0°
Units Inch
Scale 1.00

Simulation Info

Simulation name Tesla Roadster - public 3D model
Date Created Oct 19, 2026
Number of Cells 9,475,542
Solver Type RANS - steady state
Turbulence Model k-omega SST
Density 1.225 kg/m³
Viscosity 1.47e-05 m²/s

Convergence

Simulation Convergence Metrics

Convergence Graph

Performance

Coordinate Systems

Wind tunnel coordinate system (shown on images): origin set to the center of the object and the axes aligned with the air vector

Model Coordinate System: origin location & axis orientation as provided with the original 3D file

Wind tunnel coordinate system - top view

FLOW
FLOW
FLOW
Wind tunnel coordinate system - top view
Fx Fy

Wind tunnel coordinate system - left view

Wind tunnel coordinate system - left view
Fx Fz

Forces

The aerodynamic force acting on the object due to the airflow is resolved into three orthogonal components:

Fx – Drag Force: Acts parallel to the direction of the incoming wind.

Fy – Lateral Force: Acts perpendicular to the wind direction in the horizontal plane.

Fz – Lift Force: Acts perpendicular to the wind direction in the vertical plane.

Negative values indicate a force acting in the direction opposite to the arrows shown below.

There are two ways in which the wind generates force:

Pressure force: Arises from the pressure difference between two opposite sides of an object. It is the sum of all the local forces pushing or pulling perpendicular to the surface.

Friction force: Arises from the wind sliding across the surface of the object. It is the sum of all the local friction forces parallel to the surface.

Forces

The aerodynamic force acting on the object due to the airflow is resolved into three orthogonal components:

Wind Tunnel Coordinate System

Forces ● Fx ● Fy ● Fz
Pressure N
4.37e+02
-1.77e+01
7.74e+02
kg (4.46e+01) (-1.80e+00) (7.89e+01)
Viscous N
3.15e+01
9.12e-01
3.98e+00
kg (3.21e+00) (9.30e-02) (4.05e-01)
Total N
4.69e+02
-1.68e+01
7.78e+02
kg (4.78e+01) (-1.71e+00) (7.93e+01)

Model Coordinate System

Forces ● Fx ● Fy ● Fz
Pressure N
4.37e+02
-1.77e+01
7.74e+02
kg (4.46e+01) (-1.80e+00) (7.89e+01)
Viscous N
3.15e+01
9.12e-01
3.98e+00
kg (3.21e+00) (9.30e-02) (4.05e-01)
Total N
4.69e+02
-1.68e+01
7.78e+02
kg (4.78e+01) (-1.71e+00) (7.93e+01)

Moments

The aerodynamic moments acting on the object due to the airflow is resolved into three orthogonal components:

Wind Tunnel Coordinate System

Forces ● Mx ● My ● Mz
Pressure Nm
-2.60e+00
-3.79e+02
7.13e+00
kg·m (-2.65e-01) (-3.87e+01) (7.27e-01)
Viscous Nm
5.00e-01
4.72e+00
-2.84e-01
kg·m (5.10e-02) (4.81e-01) (-2.90e-02)
Total Nm
-2.10e+00
-3.75e+02
6.84e+00
kg·m (-2.14e-01) (-3.82e+01) (6.98e-01)

Model Coordinate System

Forces ● Mx ● My ● Mz
Pressure Nm
2.47e+03
-2.56e+03
-1.44e+03
kg·m (2.52e+02) (-2.61e+02) (-1.47e+02)
Viscous Nm
1.26e+01
1.21e+01
-9.75e+01
kg·m (1.28e+00) (1.23e+00) (-9.94e+00)
Total Nm
2.48e+03
-2.55e+03
-1.54e+03
kg·m (2.53e+02) (-2.60e+02) (-1.57e+02)

Aerodynamic Coefficients

The coefficients below indicate the aerodynamic performance of your vehicle (all of them have been corrected for in terms of blockage factor).

Aerodynamic performance of your vehicle

The drag coefficient was computed using the reference area defined in the Nomenclature and the velocity

Drag Coefficient
Cd 0.386
Lift Coefficient
Cl 0.64
Lift/Drag Ratio
L/D 1.66
Frontal Area
A 2.56 m²

Reference Drag Coefficient Values

The scale illustrates typical Cd values. More streamlined objects will have a low Cd, less streamlines objects will have a high Cd. The Cd of your project has been indicated as well.

Please note that this is an indicative figure, mainly suited for comparing different concepts. For a highly accurate value, contact us at info@airshaper.com.

0.386
0.0
0.5
1.0
1.5

Force and Power Curves

For your project, that leads to the force & power curves shown below. Please keep in mind that this curve is an estimation, based on extrapolation from the simulation wind speed. For more accurate forces at a given velocity, please perform a simulation for that velocity.

Drag Force Curve

Drag Force Fd(N)
468.84 N

Power Curve

Power P(kW)
13.02 kW

Energy Loss / Drag

Underpressure zones are areas with a pressure lower than that of the local surrounding air. Often these zones are caused by abrupt changes in shape, most pronounced by abrupt changes in cross section or surface geometry. Smooth these out to lower drag.

The following images provide insight into which features of your object are causing drag by showing "clouds" of low pressure.

0
0

Total Pressure Coefficient (Cp)

Perspective
Front

Front

Back

Back

Top

Top

Bottom

Bottom

Left

Left

Right

Right

Surface Pressure

Surface pressure shows how air pressure is distributed across the object. Overpressure (Cps near +1) occurs where airflow decelerates, while underpressure (negative Cps) forms where it accelerates. Both contribute to drag — smooth transitions between high and low pressure regions to reduce it.

-1
1

Cps

Perspective
Front

Front

Back

Back

Top

Top

Bottom

Bottom

Left

Left

Right

Right

Surface Friction

Friction drag is caused by air sliding across the surface. The faster the air moves, the higher the friction force. A smooth surface can reduce friction drag.

The images below show friction drag mapped in color on the surface. Surface streamlines reveal flow detachment: straight lines indicate attached flow, while curly patterns indicate separation – a common source of increased drag.

0.00
2.89

N/m²

Perspective
Front

Front

Back

Back

Top

Top

Bottom

Bottom

Left

Left

Right

Right

Streamlines

Streamlines visualize how air flows past your object. Steady lines indicate laminar flow, while swirling patterns reveal turbulence. Separation occurs when airflow detaches from the surface — typically due to sharp angles or geometric disturbances — and is a common source of increased drag.

0
41.67

m/s

Perspective

Vertical Streamlines

Front

Front

Back

Back

Top

Top

Bottom

Bottom

Left

Left

Right

Right

Horizontal Streamlines

Front

Front

Back

Back

Top

Top

Bottom

Bottom

Left

Left

Right

Right

Vortices (Q-Criterion)

Vortices are swirling regions of airflow that typically form behind sharp edges, protrusions or abrupt changes in shape. They are visualized here using the Q-criterion, which highlights zones where rotation dominates over shear, colored by the local air velocity.

Vortices consume energy and are a common source of drag. Trace them back to the geometry that creates them and smooth or streamline those features to reduce losses.

0
41.67

m/s

Perspective
Front

Front

Back

Back

Top

Top

Bottom

Bottom

Left

Left

Right

Right

Noise Generation

Noise estimation by means of simulations is an advanced field of engineering. Therefore, more simplified models ('acoustic analogies') have been introduced to obtain a rough estimation of the local noise generation without going through prohibitively expensive simulations.

To reduce the noise generation in your design, look for the origin of these "noise clouds" in the following images. Typically, noise is generated slightly downstream of the location where the flow is disturbed. Smoothen the source and you can reduce noise generation. Avoid cavities and external parts.

Noise Generation (dB/m³)

3.98
4.48
4.98
Perspective
Front

Front

Back

Back

Top

Top

Bottom

Bottom

Left

Left

Right

Right

2D Sections

Velocity

0
41.67

m/s

Velocity Top

Top

Velocity Left

Left

Pressure

-1
1

Cpt

Pressure Top

Top

Pressure Left

Left